BLOG ENTRY 3 (week 5 + practical 2)
Hey everyone! Welcome back to my blog! π
In this week’s blog, I’m going to be talking about my week 5 lesson and practical 2. This week was my personal favourite among other ICPD lessons because it involved a lot of HANDS-ON activities such as sketching, creating a product made from just cardboards and also getting to use the fusion 360 software to bring ideas to life!
So, stay tuned to learn all about my experience!
Week 5
To kickstart our week 5 lesson, Mr Chua distributed 5 pieces of blank A4 paper to each of us. After which he proceeded to say “Let’s do some sketching everyone”. To be honest, I was a little demoralised because I wasn’t much of an artistic person. I’ve only gotten an A for art once and I’m pretty sure it was based on pure luck too (LOL you’ll see why I say this later…) ππ³
Despite all these mixed emotions I still proceeded to tackle this task with a positive mindset, in hopes that my artistic skills might have miraculously gotten better since the last time I’ve done art in school.
Mr Chua mentioned more about how sketching was relevant to our ICPD module by using the phrase:
“A picture is worth a thousand words.”
Although we have all heard of this phrase before, it wasn't till that day that I realised the true beauty of how a simple drawing reaches out to people in ways that words aren’t able to. Especially in chemical product design, it is crucial to have a clear perception of how the product is going to turn out like, in order to produce the best version of the product.
Firstly, we started off with drawing basic shapes or lines without the help of any instruments such as rulers.
Here are some of my attempts:
After drawing shapes and lines as a warm-up, we were introduced to PERSPECTIVE DRAWING. Honestly, I have never heard of perspective drawing till that day, so this definitely added on to the challenge.
Let me show you an example of a drawing from a ONE POINT PERSPECTIVE:
After learning about this concept, we were tasked to draw a carton of milk from a 1-point perspective.
Here is my drawing:
If that wasn’t enough of a challenge, Mr Chua took it a notch higher and tasked us to draw products using a 2-point perspective.
To briefly explain on 2-point perspective, here is an image:
Here is my attempt on drawing using a 2-point perspective:
In my opinion, I would say I did somewhat decent drawings for the milk and the book. However what you’re about to see next is not something you’re ready for. ππ
For our final task, we were asked to draw a coffee machine while making use of our newly learnt skills on perspective drawing. I decided to use a 1-point perspective for my drawing. Halfway into my drawing, I realised that my coffee machine did not look like a coffee machine at all! Instead it looked like Lego character… π π
When I told Mr Chua this he was so amused and couldn’t stop laughing HAHHA because he in fact saw it too!
So without any further-ado, here’s my coffee machine (Lego man) from a 1-point perspective:
Told you I wasn’t great at art… ππ³
Since my initial drawing did not exactly come out as a coffee machine, I decided to try again. Here’s a picture of my somewhat improved drawing using a 2-point perspective:
OVERALL, this session was beneficial for us as we got to learn about drawing from different perspectives and this was also good practice for when we drew our chemical product for our CA1 report. Through this activity, I also got to bond with my team members as we kept comparing our drawings and getting a good laugh here and there.
After discussing the dimensions of our chemical product for our CA1 report, we decided on using 2-point perspective for our drawing.
Here is how our product turned out :
Since our team decided to focus on the idea of recycling materials, our chemical product is an insect-repelling coffee candle that is made from used coffee grounds and soybean wax to ensure that final product is environmentally friendly. The dimensions of the candle are 50mm by 50mm by 80mm, held together in a used glass container with a thickness of 5mm.
FUSION 360
During this week we had the opportunity to manipulate the Autodesk Fusion 360, a software that we had no prior experience with. The Autodesk fusion 360 is a software used to create 3D models that can later be 3D printed to form a final product. Initially, it was confusing for me to manipulate the software because it kept lagging and I was too nervous because I feared I might click the wrong buttons.
However, our lecturer Mr Chua patiently guided us through the different functions of the software such as “extrude”, “sketch” and adjusting dimensions of our 3D model. With this, we managed to create a personalised key tag!
After warming up to the software, we were tasked to create different components of a photo frame and combine all the components together as the final step. My group and I distributed our tasks equally and we each picked out the component of our choice. I had picked out the PHOTOBACK.
It was intimidating to manipulate the software initially but with the help of Brightspace and teamwork, I managed to finish the task!
Here is the embedded link of my photo back!π
<iframe src="https://ichat3591.autodesk360.com/shares/public/SH35dfcQT936092f0e43d2696fba9e3a3932?mode=embed" width="640" height="480" allowfullscreen="true" webkitallowfullscreen="true" mozallowfullscreen="true" frameborder="0"></iframe>
After all of us were done with our individual parts, we combined our components to form a photo frame!
Here’s an embedded link of our photo frame!π
<iframe src="https://ichat3591.autodesk360.com/shares/public/SH35dfcQT936092f0e4314013234ee72597b?mode=embed" width="640" height="480" allowfullscreen="true" webkitallowfullscreen="true" mozallowfullscreen="true" frameborder="0"></iframe>
I am glad despite all the obstacles we faced when we tackled this software, we managed to reach the end goal and create the photo frame!
Practical 2
During practical 2, we had to create a cardboard model of our choice, using any 6 cardboard joineries. Before talking about these carboard joineries and their uses, let me share with you on some information we picked up on during our pre-experiment literature review on corrugated fiberboards.
A sheet of corrugated cardboard is made of 3 components, a sheet of corrugated (fluted) material in the centre, placed between 2 layers of paper (liners).
There are 2 main types of paper that are used for the liners, Kraft and Test papers. Each liner type consists of a basic layer for adhesion and strength, as well as a cover layer for aesthetic purposes.
Kraft- manufactured from softwood trees being the strongest and easiest to print on, hence it is commonly used as outside liner for purposes such as packaging.
Test- recycled double layered paper. Since it's recycled, it is not as strong or as easy to print on as Kraft. Hence it's used as an inner liner and it's cheaper than Kraft.
Flute - “corrugated” section between the two liners. The flute type has a significant impact on the performance of the cardboard, as well as the cost and weight. Modifying its height affects its performance characteristics and hence its applications. The thicker the cardboard, the heavier the load that it can carry.
We also learnt that cardboards have many layers of walls and that each different layer aids with different tasks. Before we engaged in any hands-on activity, Mr Chua educated us on the different types of joinery.
What is a joinery? (you may ask…)
Well here’s a picture with examples of some joinery types:
The purpose of joinery is to hold to hold the cardboard pieces strongly and securely, while also having aesthetic purposes occasionally. Before moving on to handling the cardboards, we were also equipped with useful skills such as cutting along the corrugations instead of cutting against them so as to ensure that cutting can be done with ease.
The main objective of practical 2 was to come with any product that made use of 6 joinery types. We were given various equipment such glue guns, penknives, rulers, tapes, skewers and fasteners that we could use in our final product. My group members and I started brainstorming and generating potential ideas of what our product should be.
We finally decided on creating a KATANA. Mind you, this was not going to be any ordinary sword as we were going to create a personalised sword sieve and sword stand, so that our product stood out. We planned to name our sword “FLAME HASHIRA” as inspired by demon slayer. π₯
We immediately kickstarted our model by coming up with various sketches on how our final product was going to look like. Here’s a picture of some of our sketches:
To be more efficient in our tasks, we distributed tasks evenly among all 5 of the members so that we would finish our creation within 2 hours. I was in charge of making the sword stand, alongside my group mate Jun Yi.
Dimensions were a crucial factor to take note of for our product as the sword would not function properly if the dimensions were not properly thought through. Hence, we had to make use of various physics concepts to estimate if the sword would sit on the stand with stability.
Although there were some varying opinions that were raised during the activity, there were no disagreements that had arised as we managed to illustrate our thoughts on paper so that everyone was on the same page. We also made it our utmost priority to abide by the safety protocols such as wearing work gloves when handling with the glue gun or penknives. Goggles and PPE were also diligently worn and thus we could safely carry out with the activity!π
HERE ARE SOME PICTURES OF US CREATING OUR KATANAπͺπͺ
For the final component of our practical, we were required to present our cardboard model to the class and talk about the 6 joineries that we had implemented into our design.
These are the 6 joinery types we had used:
- - Tabs and skewer to secure the sword onto the handle
- - Flange used in the handle of the sword
- - Insert used to support sword when placed onto the stand
- - Brass fasteners used to open and close the sieve of the katana
- - L-brace used in the katana sieve
HERE IS OUR FINAL PRODUCT (FLAME HASHIRA) ππͺπ₯
Overall, this practical was very engaging and a new experience for all of us! It also gave us a glimpse on how a product designing process would feel like! That’s all for this week guys, hope you’ve enjoyed this blog as much as I did!
Let me end off by inserting a picture of my group and our LOVELY lecturer, Mr Chua ππ
BYE GUYS! ππ








.jpeg)


Comments
Post a Comment